Noise insulation / disassembly of a front doors. Photoreport

Noise insulation of front doors by own strength.

I has decided to do noise insulation by own strength.
For absolute correctness of the stated material I do not apply, but like all made by rules.
Process this creative, variants are possible.

Materials:

Vibro isolation
StP Bany M1 the Size of a sheet 75*53 cm - 67 UAH (14 USD)
4 sheets
Noise isolation
StP Poly-4L the Size of a sheet 125*100 cm - 75 UAH (15 USD)
1 sheet
Bit-5L the Size of a sheet 200*100 cm - 175 UAH (35 USD)
1 sheet

Tools:
The platen, painting adhesive tape, scissors, writing knife, white-spirit, a knife, a ruler, a marker,
Cloths

1. Disassembly of a door is begun with removal tweater.
Tweater is removed, having pulled on itself by the top corner. It is possible to shift slightly aside the door handle and
Besides to pull on itself. If it is impossible to remove at once, in a gap between a tweater cover and
a frame of a door it is inserted improvised means of type of the screw-driver which have been turned in a fabric, that not scratches a paint. By means of such lever remove a cover.
The cover tweater keeps on two latches.

2. Turn off a screws of the door covering. There are three pieces. Two on a cover of the door , one in the butt of a door.
Plug I hooked a knife.

In the butt end of the door do not mix plug with fastening screw
I mixed at first. Here a photo with removed plug

3. Take off door card. It is better to begin from the side of mirror. Beginning from top to bottom on a perimeter, clockwise (for the left door) open with a snap percussion caps.
Be not afraid and pull on itself a card, if to pull very poorly, percussion caps can remain in doors.

Further probably two variants. Removal of a card<-> connection/switching-off of a switch of the electric drive of door glasses or on the contrary.

Variant 1.

Insert a key into the lock of ignition.

When all percussion caps (9 pcs) opened with a snap- raise a card upwards.
Carefully take off it. Allocate aside that technological apertures of a casing were visible

Remove elastic bands from apertures.
Lower a little glasses while in apertures bolts of fastening of glasses will not seem.

It is necessary open with a snap 2 switches of electric wiring - the block of control of mirrors and the block of the electric drive of glasses.
Draw out a card upwards.

4. Admire a pure metal casing.

5. Glasses.
Paste a painting adhesive tape that it held glasses.

Turn off bolts from technological apertures in a casing.
Take in hands a painting adhesive tape and scissors.
Lift glasses in the top position and fasten a painting adhesive tape.

One person can make all this.

Connect a switch of the electric drive of glasses and pull down glasses

6. A casing.
Turn off (it seems 9) bolts spanner "on 10".
Try to take off a casing, accurately as behind a casing it is necessary to disconnect a rope of the handle of opening of a door and a switch to the central lock.
The wire of a switch to the central lock fastens percussion caps, they should be disconnected.

Then take out a rope through the aperture and remove a casing.
Far it you will not carry away, but about doors to attach it is possible.

7. Admire a panel of a door

The door is ready for work.

8. Clear a surface of a panel of a door the rags moistened in white-spirit.

9. Mark a material and glue on panels "Vibroplast М1 (StP Bany M1)".
I have stuck even pipes, but it more likely exception of a rule.
Will enough paste over a plane of a door.

10. Now try to put a metal casing back. Do everything in a reverse order.
When return glasses on the places it is necessary to press them as it is possible more close to that side, where the door handle. If to lower glasses a self-feed, the skew is possible and they completely will not be closed, there can be chink.
Checked up the rightness of adjoining of glasses by connecting of switch of the electric drive of glasses and raising/lowering of glasses.

Possible problems: when insert a switch of the central lock, it does not become on a place, thus the central lock can click three times.
The reason: in a switch there is a double rubber sealant. The central lock relay clicks because of bad contact.
The decision: it is possible to try to push force a switch (thus something to break), and it is possible to cut off one ring of a sealant of a switch. Then it it becomes good on the place, and the relay will not click.

11. Further creative process. Processing of a surface and gluing Vibroplast M1 (StP Bany M1) on a casing (as your fantasy allows you)

12. Analogical process - the second layer glue "splan" StP Poly-4L.

13. Door cards(maps).
On the back of door cards glue "bitoplast" Bit-5L.
A process is creative again.

At glueing all types of materials it is recommended to smooth well a material that it densely adjoined.
It is possible to use pressing roller for glueing wall-papers, the same roller of a painting adhesive tape, etc.

14. Assembly.
Now try to return everything on the places and fasten a door card.
Before an attachment I have just in case sprinkled a little percussion caps by WD-40.
Put a card on a place, connect switches and a rope of the handle of opening of a door.

Turn on screws. If will not find former apertures, it doesn't matter, they can be glued by "splan" StP Poly-4L. All the same turn on in the put places.
It is not forgotten to put a choke.

Play music and already see/hear result of work :-)

"Fidget"
Sorry for my English